Boundary Conditions
Perfect electric conductor (PEC) boundary
The perfect electric conductor (PEC) boundary condition (zero tangential electric field) is specified using the "PEC" boundary keyword under config["Boundaries"]. It is a homogeneous Dirichlet boundary condition for the frequency or time domain finite element formulation, as well as the magnetostatic formulation.
For electrostatic simulations, the homogeneous Dirichlet boundary condition is prescribed using the "Ground" boundary keyword which prescribes zero voltage at the boundary.
Perfect magnetic conductor (PMC) boundary
The perfect magnetic conductor (PMC) boundary condition (zero tangential magnetic field) is a homogeneous Neumann boundary condition for the frequency or time domain finite element formulation, as well as the magnetostatic formulation. It is the natural boundary condition and thus it has the same effect as not specifying any additional boundary condition on external boundary surfaces. It can also be explicitly specified using the "PMC" boundary keyword under config["Boundaries"].
Likewise, for electrostatic simulations, the homogeneous Neumann boundary condition implies a zero-charge boundary, and thus zero gradient of the voltage in the direction normal to the boundary. This is specified using the "ZeroCharge" boundary keyword under config["Boundaries"].
Impedance boundary
The impedance boundary condition is a mixed (Robin) boundary condition and is available for the frequency or time domain finite element formulations and thus for eigenmode or frequency or time domain driven simulation types. It is specified using the "Impedance" boundary keyword. The surface impedance relating the tangential electric and magnetic fields on the boundary is computed from the parallel impedances due to the specified resistance, inductance, and capacitance per square.
Absorbing (scattering) boundary
Absorbing boundary conditions at farfield boundaries, also referred to as scattering boundary conditions, can be applied using the "Absorbing" boundary keyword under config["Boundaries"]. The first-order absorbing boundary condition is a special case of the above impedance boundary and is available for eigenmode or frequency or time domain driven simulation types. The second-order absorbing boundary condition is only available for frequency domain driven simulations.
Perfectly matched layer (PML) boundaries for frequency and time domain electromagnetic formulations are not yet implemented, but are common in solvers for computational electromagnetics and will be a useful addition.
Finite conductivity boundary
A finite conductivity boundary condition can be specified using the "Conductivity" boundary keyword. This boundary condition models the effect of a boundary with non-infinite conductivity (an imperfect conductor) for conductors with thickness much larger than the skin depth. It is available only for frequency domain driven simulations. For more information see the Other boundary conditions section of the reference.
Lumped and wave port excitation
config["Boundaries"]["LumpedPort"]: A lumped port applies a similar boundary condition to a surface impedance boundary, but takes on a special meaning for each simulation type.For frequency domain driven simulations, ports are used to provide a lumped port excitation and postprocess voltages, currents, and scattering parameters. Likewise, for transient simulations, they perform a similar purpose but for time domain computed quantities.
For eigenmode simulations where there is no excitation, lumped ports are used to specify properties and postprocess energy-participation ratios (EPRs) corresponding to linearized circuit elements.
Note that a single lumped port (given by a single integer
"Index") can be made up of multiple boundary attributes in the mesh in order to model, for example, a multielement lumped port. To use this functionality, use the"Elements"object under"LumpedPort". Also, each element of a lumped port boundary must be planar. Combining multiple planar boundaries into a single port"Index"via the multielement lumped port achieves the same effect as if the single element lumped port was made up of boundaries which were not coplanar.config["Boundaries"]["WavePort"]: Numeric wave ports are available for frequency domain driven simulations. In this case, a port boundary condition is applied with an optional excitation using a modal field shape which is computed by solving a 2D boundary mode eigenproblem on each wave port boundary. This allows for more accurate scattering parameter calculations when modeling waveguides or transmission lines with arbitrary cross sections.The homogeneous Dirichlet boundary conditions for the wave port boundary mode analysis are taken from the
"PEC"boundaries of the full 3D model, as well as any optional additional boundary attributes given under"WavePortPEC". Any boundary of the wave port not labeled with with a PEC condition has the natural boundary condition for zero tangential magnetic field prescribed for the purpose of port mode calculation.Unlike lumped ports, wave port boundaries cannot be defined internal to the computational domain and instead must exist only on the outer boundary of the domain (they are to be "one-sided" in the sense that mesh elements only exist on one side of the boundary).
Wave ports are not currently compatible with nonconformal mesh refinement.
The incident field excitation at a lumped or wave port is controlled by setting config["Boundaries"]["LumpedPort"][]["Excitation"]: true or config["WavePort"][]["Excitation"]: true for that port. The excitation for each port is defined to have unit incident power over the port boundary surface.
Surface current excitation
An alternative source excitation to lumped or wave ports for frequency and time domain driven simulations is a surface current excitation, specified under config["Boundaries"]["SurfaceCurrent"]. This is the excitation used for magnetostatic simulation types as well. This option prescribes a unit source surface current excitation on the given boundary in order to excite the model. It does does not prescribe any boundary condition to the model and only affects the source term on the right hand side.